|
CLEANING AND RESTORING BUTTONS
by Lisa Schulz
Button Images
www.buttonimages.com
Before cleaning your buttons you will need to know what
materials the buttons are made of and have a knowledge of their construction and
makeup, because the various materials are treated differently.
Many of the following cleaning techniques have been
suggested by other collectors. They have not all been tested by this writer.
There are several things that this writer has used very
successfully, and would recommend keeping in your cleaning supply kit. They
are:
- Polishing Cloth (see my catalog or web site for ordering
Polishing Cloths.) With use the cloth will get black, but it still continue
to clean your buttons. I keep one for metal buttons and another (cleaner one)
for other materials. Do not wash the Polishing Cloth.
- Brass Brush (see my catalog or web site for ordering
Brass Cleaning Brushes.) Can be used on brass buttons without scratching.
Can be used on other types of metal with a little more caution (brush
gently). Use caution on fine silver and pewter.
- Gray ink eraser (found with school supplies or an office
supply store.)
- Lead Pencil.
- Baby oil, mineral oil or gentle furniture polish used
with a sort cloth.
- Clean dry tooth brush. Most buttons can be brushed with
a tooth brush to remove dirt or dust that is on the surface or in cracks.
- Dremel with eraser wheels and brass brushes. (Can be
purchased at some WalMart stores, some hobby stores or hardware stores) – The
eraser wheels come in black, blue, and pink, with black being the harshest and
the pink being the most gentle. I recommend beginning with the gentle eraser
wheel (pink) and work your way up to the black if you need to. Put a
mounting wire through the shank and use this wire to hold the button securely
while cleaning it. Turn on the Dremel and touch the button very gently with
the wheel. CAUTION: It is very easy to over polish your button using this
method.
- Vibratory Tumbler - more details on this method at end
of article.
Always be EXTREMELY cautious when cleaning buttons that
have paint on them. Paint is easy to remove or chip using many of these
methods.
I do not use any type of polishing creams or pastes. The
creams and pastes tend to get down into the cracks and are extremely difficult
get out of the tiny spots. If you already have brass buttons with polish
deposits in the cracks of the button, the Brass Brush listed in my catalog works
great for cleaning it out.
I suggest that you try cleaning your less expensive
buttons first, to gain experience, before attempting to clean your more deluxe
buttons. The wrong cleaning method can destroy a button, so be careful!!!
Many materials listed here have more than one cleaning
method listed. That does not mean you have to use all if them. It means there
are a number of methods available for cleaning those materials. If one method
does not work on your button, try another.
In all cases a little more caution will need to be used if
there is any type of embellishment on the button.
Bone
- Wipe with a clean polishing cloth.
- Cut a lemon in half, dip it in salt and rub over
surface, wipe with damp cloth and dry.
Celluloid
- CAUTION: Most paints and stains are not permanent, so
clean very gently.
- NEVER submerge in water.
- Wipe gently with a polishing cloth.
- If crackled and/or chalky the button is probably
deteriorating and very little can be done to restore it. Keep separate from
ALL other buttons.
Ceramic
- If the ceramic has been baked the button can be wiped
with a dry or slightly damp cloth, or wiped with mild soapy water.
- If the ceramic is not baked, just painted, it will be
difficult to clean without removing the paint.
Composition
- Wipe with a polishing cloth.
- Use baby oil, mineral oil, or furniture polish on a soft
cloth, wipe gently. Wipe the button again with a clean, dry cloth, to remove
excess oil or polish.
- Natural self-shining shoe polish can be used to give the
buttons a shine.
Copper
- Wipe/rub with a polishing cloth.
Enamel - (Be careful not to confuse painted metal
buttons with enameled ones. Painted buttons have not been baked. The paint may
be brittle and flake off easily. DO NOT use these methods if the button is
painted, they WILL remove paint.)
- Wipe gently with a polishing cloth.
- Silver polish can sometimes be used with care.
- Use a cloth just slightly, moistened with household
ammonia, wipe the button very gently. Will remove the dust and dirt, but not
the enamel.
- In some cases dirt can be removed by using a small
amount of toothpaste on a clean, dry cloth. Wipe the button gently. Wipe
again with a clean, dry cloth to remove all toothpaste.
- Motawala enamels are a camera technique and are not
fired. Take great caution in cleaning them. DO NOT use water, a silver
polish, ammonia or any type of moisture.
Fabric
- NEVER rub or brush the fabric, even if material seems
strong. The threads are often brittle and break easily.
- Put a small amount of fabric dry cleaning fluid into a
glass jar. Put the buttons into the fluid and gently shake the jar for a
minute or two. Remove buttons, lay on absorbent cloth (or towel), outdoors
(or in front of an open window), to dry. The air will help to evaporate the
fluid. DO NOT use this method if there is trim or embellishment on the button
that has been glued on rather than sewed on.
Glass
- Be very cautious when cleaning buttons with luster and
paint. It may rub off easily if it has not been fired on. Clean with
caution.
- With CARE, wipe painted glass very gently with a dry
cloth, a clean polishing cloth, or slightly damp cloth.
- If decoration has been fired on the button, it can be
cleaned with a damp cloth of mild soapy water.
- Very dirty buttons with no paint, luster or
embellishment, can be wiped gently with a damp cloth, or Windex.
- Glass with foil under glass should be wiped with a dry
cloth.
- One-piece glass with a self-shank and no paint, no
luster, and no embellishment can be put in a mild sudsy water, then rinsed,
and dried thoroughly.
Horn
- DO NOT use water.
- Wipe with a polishing cloth.
- Use a soft cloth with either furniture polish or mineral
oil, then wipe with clean dry cloth.
- Can rub a bit of lanolin into the surface of the button,
after a few minutes wipe with a clean dry cloth.
- Color can be restored by rubbing with a good quality
paste shoe polish, apply with a cloth, remove the excess.
- Soft brush can be used to clean dust and dirt out of
cracks.
- Holes in horn buttons caused by insects--Place buttons
in a plastic bag and put in the freezer for a week. This should kill any
remaining insects and their eggs.
Ivory
- Wipe with a clean polishing cloth.
- Cut lemon in half, dip in salt and rub over surface,
wipe with damp cloth and dry.
- Wipe with soft cloth and baby oil. Wipe dry.
Leather
- Wipe with a polishing cloth.
- Use saddle soap, Neetsfoot Oil, or neutral shoe cream.
- Baby oil and mineral oil also work well.
- Take caution if there is embellishment on the button.
Metal/Brass
- NEVER submerge two-piece buttons into any liquid. Many
of them have a cardboard disk in the center, which will absorb water, and
eventually destroy the button.
- Brush well with a high quality brass brush. This will
remove the green powder, but not scratch the button. Also works well for
cleaning groves in buttons, and shining them a bit.
- Wipe or rub with a polishing cloth.
- Rub with wool carpet.
- Rub gently with an ink eraser.
- Rub gently with Q-tip covered with acetic acid as in
vinegar, catsup, and Worcestershire Sauce. Then wipe clean with a dry cloth.
Take caution using this method if the button is made of more than one piece,
liquid could get in between the layers and would be difficult, if not
impossible, to remove.
- CAUTION: All types of Brass or Metal polish tend to
leave a residue in the cracks and small areas, which is difficult to wipe
out. Over time, the polish residue can eat into the surface of the metal if
left there.
- A brass brush can be used to remove residue that is
already on your button.
- A brass brush on a Dremel can also be used, but eye
protection is a MUST, as splintering of the brass may occur.
- A silicone rubber wheel (eraser type wheel) on a Dremel
can also be used. Eye protection is a MUST. CAUTION: Be careful not to over
polish.
- BE CAUTIOUS cleaning buttons with original tint. Many
methods will remove the tint.
Pewter
- Wipe with a polishing cloth.
- Brush very gently with a high quality brass brush.
CAUTION: Some pewter is very soft and may scratch easily.
- Use the outer leaf from a head of cabbage, as a
polishing cloth, then buff with a soft cloth.
- Use Turtle Wax or chrome polish.
Silver
- Wipe with Polishing Cloth.
- Use a good silver polish.
- CAUTION: All polishes tend to leave a residue in cracks
and small areas that are difficult to wipe out. Use a brass brush to remove
the residue, it can eat into the surface of the metal if left there.
- Never store in or around rubber (including rubber
bands). The rubber actually “melts” into the silver and can destroy the
silver.
Steel
- BE CAUTIOUS with tinted steels. Many polishes can
remove the tint.
- Wipe with a polishing cloth
- Brush well with a high quality brass brush.
- If rusty, rub the rusty area with the lead of a pencil
or an ink eraser to remove rust. Wipe with a clean cloth. With time the rust
may return.
- Rust can be removed with a commercial rust remover such
as Rust Eater, WD-40 or Naval Jelly, and may prevent further rust. Apply
carefully with a cotton swab, let set for a little while (or over night),
remove with more cotton swabs or a soft dry cloth. Then polish with Polishing
Cloth.
- Use 000 steel wool to remove rust on backs and shanks of
steel buttons.
- Always make sure your hands are dry when working with
steel.
- A brass brush on a Dremel can also be used, but eye
protection is a MUST, as splintering of the brass brush may occur.
- A silicone rubber wheel on a Dremel can also be used.
Eye protection is a MUST. Be careful not to over polish. If buffing is then
needed it can be done with a polishing cloth or a felt wheel on the Dremel.
- All cream polishes tend to leave a residue in the cracks
and small areas. It is difficult to wipe out. Use a brass brush to remove
the residue. The polish residue can eat into the surface of the metal if left
there.
Tin or Zinc
- Wipe with a polishing cloth.
- Rub with a soft eraser.
Uniform buttons
- NEVER submerge two-piece buttons into any type of
liquid.
- Wipe with a polishing cloth.
- Brush with a high quality brass brush.
- Rub with wool carpet.
- A brass brush, on a Dremel, can also be used, but eye
protection is a MUST, as splintering of the brass brush may occur.
- A silicone rubber wheel on a Dremel can also be used.
- Polish with a high quality metal polish. All polishes
tend to leave a residue in cracks and small areas that are difficult to wipe
out. Use a brass brush to remove the residue. The polish residue can eat into
the surface of the metal if left there.
- CAUTION: Be careful not to over polish.
White metal
- NEVER submerge two-piece buttons into any type of
liquid.
- Wipe with a polishing cloth.
- Brush with a high quality brass brush.
- Rub the dingy areas with a crumpled piece of aluminum
foil.
- Rub with wool carpet.
- Polish with a high quality metal polish. All polishes
tend to leave a residue in cracks and small areas that are difficult to wipe
out. Use a brass brush to remove the residue. The polish residue can eat into
the surface of the metal if left there.
- Can make your own polish by making a paste of three
parts baking soda and one part water.
- DO NOT over polish.
Yellow metal
- NEVER submerge two-piece buttons into any type of
liquid.
- Wipe with a polishing cloth.
- Brush with a high quality brass brush.
- Rub with wool carpet.
- Some have suggested rubbing your button on newspaper
- A brass brush on a Dremel can also be used, but eye
protection is a MUST, as splintering of the brass brush may occur.
- A silicone rubber wheel can also be used on a Dremel.
Eye protection is a MUST.
- Polish with a high quality metal polish. All polishes
tend to leave a residue in cracks and small areas that are difficult to wipe
out. Use a brass brush to remove the residue. The polish residue can eat into
the surface of the metal if left there.
- Make your own polish with a paste of 1 tablespoon each
of salt, flour and vinegar. Use a soft cloth to apply the polish.
- DO NOT over polish.
Pearl or Shell
- Wipe with a polishing cloth.
- If there is no paint or embellishment on the button it
can be cleaned with a soft brush and mild soapy water.
- Luster can often be restored by rubbing with a soft
cloth moistened with baby oil or mineral oil. If there is no trim or painting
on the button you may soak it in mineral oil or baby oil for a while. Then
wipe dry with a clean cloth.
- If there is other material embellishment, try wiping
with a dry cloth, or a polishing cloth.
Plastic
- Wipe with clean polishing cloth.
- Wipe with a damp cloth.
- If one-piece and no paint on button can be washed in
mild soapy water.
- Dry thoroughly.
Rubber
- Wipe with a clean polishing cloth.
- Wipe with a small dab of furniture polish or baby oil,
on a soft cloth. Dry thoroughly.
- A soft brush can be used to remove dust and dirt from
the deeper designs.
- On black rubber one can use a high quality black shoe
polish to restore color.
- Avoid soap and water.
Turquoise
- Use a soft dry cloth. DO NOT use water.
Vegetable Ivory
- Wipe gently with a clean polishing cloth.
- Do not use water.
- Polish with Kiwi Leather Balm. Dry thoroughly.
- Use a soft cloth with furniture polish, baby oil or
mineral oil. Dry thoroughly.
Wood
- Do not use water.
- Wipe with a clean polishing cloth.
- Clean like furniture, if no paint, trim, or other
material embellishment one can use a soft cloth with furniture polish, baby
oil or mineral oil.
- Be cautious with those that have other material
embellishment. Many other embellishments will not take well to furniture
polish.
THINGS TO REMEMBER:
- DO NOT over-clean or over-polish your buttons.
- NEVER dump a box of buttons into a pan of water no
matter how dirty they are.
- Take special caution when cleaning buttons of several
materials.
- Be gentle, a tender touch is best.
- DO NOT use water on most buttons.
- Some types of polish can destroy golden age buttons, as
well as other buttons with a gold finish.
- DO NOT use olive oil or vegetable oils, with time they
can become rancid.
- Exposure to sun and air will not harm most buttons.
- Radiation of the sun’s rays will kill fungi and mildew.
Allow them to heat gradually.
- DO NOT take buttons from a cool place and put in the
direct sunlight, some materials may crack.
- DO NOT use any type of liquid when cleaning glass
mounted in metal. The moisture will get under the glass.
- Japanese metalwork is often difficult to polished.
- NEVER submerge two-piece buttons into any type of
liquid. Many of them have a cardboard disk in the center, which will absorb
the liquid and eventually destroy the button.
- DO NOT mount buttons with pipe cleaners, safety pins,
paper clips, or steel wires. Over time, these materials will rust, causing
damage to the shanks of your buttons.
- It is best to use copper wire, or coated copper wires
for mounting buttons. They will not rust or cause damage to your buttons.
STORAGE OF BUTTONS
- Celluloid should be stored alone. Celluloid buttons are
highly corrosive of brass and steel if stored together. There is Camphor in
the celluloid which reacts with metal, causing deterioration to both
materials.
- Plastic buttons should be stored alone. Some plastics
contain carbolic acid. With time those buttons will be destroyed themselves,
as well as buttons that come in contact with them, particularly metal
buttons. They will also destroy the metal shanks.
- Metalized plastic should also be stored alone. It too
is highly corrosive of brass if stored with brass. It is also corrosive to
some other materials if stored together.
- In general it is best to store like materials together.
- DO NOT store buttons in air tight containers. It is
best to store them where air can circulate around your buttons, and where they
can breathe.
ODORS/MUSTY SMELLS
- Place buttons (not celluloid or plastic) in direct
sunlight for a day. Some times the sun will remove the odors.
- Place buttons in a bag with a dryer sheet of fabric
softener. Leave for several days.
CLEANING QUANTATIES OF BUTTONS with a Vibrator Tumbler
There is a vibrator tumbler that is used by non button
collectors to clean small parts (such as gun parts) or rocks. It works wonders
on many types of buttons as well. The machine has a motorized base and annular
tumbling bowl with a lid.
This is what my machine looks like.
The buttons are vibrated in the machine, along with ground
walnut hull media. (Ground corn cobs can also be used, but I have been told
that they need to be replaced more frequently than the walnut shells.)
I have put a wide variety of materials in my machine, all
at the same time. I have put in most types of metal, glass, Bakelite, vegetable
ivory, pearl, and Lucite.
The Vibrator Tumblers come in a wide variety of models and
sizes. Regardless of size, they are all used in the same way. Make sure the
machine is setting on a hard, smooth (not carpeted), level surface with ample
clearance around it, to allow proper air flow to the motor. Fill the bowl about
1/3 to ˝ full will the walnut hull media. (I do not use the media with rouge in
it. Some types of rouge media can give some buttons a redish tint.) Add the
buttons you want to clean. (I have had a couple hundred buttons at a time in my
large size tumbler.) Screw the lid on tightly and turn it on. Buttons can be
cleaned in this method of vibrating for 24 hours or more. I have had some very
dirty or stained buttons in the machine for a week. Time is not crucial with
this machine. Shut the machine off and check your buttons periodically, until
the desired finish is attained.
To remove buttons, empty entire contents of the bowl into
a plastic sieve or strainer, which has been placed in, or on another container.
The media will go through the sieve into the container and the buttons will stay
in the sieve. If there are buttons that are not as clean as you would like,
they can be put back into the bowl for more polishing. This same media can be
used over and over again. When it appears to be dirty, discard it and replace
it with clean media.
A few CAUTIONS and suggestions:
- I would suggest you start by experimenting with your
least expensive buttons first.
- Buttons with openwork, such as cricket cages can become
filled with the media.
- Be cautious with buttons with paint, tints, or luster.
(I have had some turn out great, and others not so great.)
- The media does get caught in deep groves and under
layers or loose edges.
- Media will get inside buttons with cone type shanks that
are open. To partially prevent the media from getting inside these buttons
you can insert a small piece of pipe cleaner into the shank, and leave it
there during the tumbling process.
- Media that gets into groves and cracks can sometimes be
removed by shaking the button. If that does not work try a toothbrush, brass
brush, or the brass brush on a Dremel.
Where does one get a Vibrator Tumbler and the walnut
media?? There is a wide variety of places on the internet that sell them, as
well as many gun shops, and a few rock shops. If you want to look on the
internet, do a search for Vibrator Tumbler.
Have fun, and good luck at restoring your buttons to their
original beauty!!!!
(revised 4/2007) |
